The 30 mm bore of the 22200K Series Tapered Bore Spherical Roller Bearings is the 22206K: 30 mm bore, 62 mm outside diameter, 20 mm wide. This page gives the dimensional row from the table, the shaft and housing fits that suit it, the internal clearance to expect and the mounting, lubrication and failure notes that go with the type.
30 mm Bore Dimensional Row (ISO 15 / GB/T 288 / DIN 635-2)
| Designation | Bore d (mm) | Outer diameter D (mm) | Width B (mm) | Chamfer r min (mm) | Bore taper | Adapter sleeve | Permissible misalignment (deg) |
|---|---|---|---|---|---|---|---|
| 22206K | 30 | 62 | 20 | 1.1 | 1:12 | H306 | 1.5 |
What a 22200K Series Tapered Bore Spherical Roller Bearings Does
Two rows of barrel rollers share one spherical outer raceway. The result is the highest basic load rating available in a given envelope together with genuine self-alignment under both mounting error and shaft deflection, which is why it is the standard bearing of vibrating screens, crushers, conveyor pulleys, fans and gearbox output shafts.
Radial load, and axial load in both directions. The steep contact of the barrel rollers gives real thrust capacity, but the axial load must be kept within the manufacturer's stated ratio to the radial load — a spherical roller bearing loaded almost purely axially loses the load sharing between its two rows.
Speed at 30 mm Bore
No limiting speed is tabulated for this product. Where speed matters, the figure to work to is the one the bearing supplier states for the exact design, cage and lubricant supplied — not a family value.
Radial Internal Clearance at 30 mm Bore
Radial internal clearance is the total distance one ring can be moved relative to the other, across the bearing, before it is mounted. It is not a tolerance and not a quality grade: it is a quantity that gets USED UP on installation. An interference fit on the shaft expands the inner ring; a tight housing fit compresses the outer ring; and a shaft that runs hotter than its housing grows more than the housing does. All three subtract from the clearance the bearing was made with. C3 exists for that reason. Specify it when the shaft fit is heavier than normal, when the inner ring will run 10 °C or more above the outer, when a hollow or heated shaft is involved, or when the bearing sits on an adapter sleeve that is driven up hard. Specify CN — normal, and usually left out of the designation entirely — for the ordinary case of a moderate fit on a shaft close to housing temperature. The failure this prevents is specific and quick: fit a CN bearing with a heavy interference on a shaft that then runs hot, and the residual clearance goes negative. The bearing is now preloaded by its own installation, the rolling elements are squeezed, friction and temperature rise together, and the temperature rise tightens the fit further. It runs hot, then it runs blue, and the raceways spall long before the calculated life.
ISO 5753-1 tabulates clearance separately for each bearing type, and the numbers for this type are not the deep groove ball bearing numbers. Order the group — CN, C3 or C4 — and take the values from the table for this type.
Abutment Shoulder & Fillet Radius for 30 mm
The chamfer dimension r min for this size is 1.1 mm. That figure is a limit on YOUR machining, not just on the bearing: the fillet radius in the corner of the shaft or the housing must be smaller than the bearing's corner radius, or the ring seats on the fillet instead of on the shoulder face and is loaded on its corner.
| Chamfer dimension r min (from the table) | 1.1 mm |
|---|---|
| Maximum fillet radius on the shaft or housing | 1.1 mm |
| Shaft shoulder must exceed | 32.2 mm diameter |
| Housing shoulder bore must be under | 59.8 mm diameter |
The two shoulder figures are the geometric floor and ceiling: a shoulder outside them fouls the corner radius instead of bearing on the ring face. The practical values sit inside them — the shoulder must contact the ring face over a useful area without touching the seal, the cage or the opposite ring, and it must still leave room for a puller when the bearing is dismounted. Take the working da and Da from the abutment table for the bearing; the ring shoulder height they are built on is not a boundary dimension and is not in this table.
Mounting a 30 mm Bore 22200K Series Tapered Bore Spherical Roller Bearings
This bearing is mounted on a tapered adapter sleeve rather than on a machined interference seat. The sleeve is drawn up the shaft by its lock nut and the tapered bore expands the inner ring onto it, so the fit is created by how far the bearing is driven up the taper — measured as a reduction in radial internal clearance or as an axial drive-up distance — and the shaft itself only needs a commercial tolerance. Never judge the fit by feel: a bearing driven too far up the sleeve loses its clearance and runs hot from the first minute.
Lubrication & Relubrication
Oil is the usual lubricant here, because this type is used where the load, the speed or the heat generated is beyond what a grease charge can carry away. Oil bath, oil mist, circulating oil and jet lubrication all take heat out of the bearing as well as separating the surfaces, and the viscosity has to be selected at the OPERATING temperature — a viscosity chosen at 40 °C when the bearing runs at 90 °C is not the film thickness the calculation assumed.
Sealed-for-life versions carry their whole service life of grease inside the seals and cannot be relubricated. That is the right choice where the bearing is inaccessible and the duty is mild; it is the wrong one where the temperature is high, the environment is wet, or the required life is longer than the grease life — and the grease, not the steel, is what ends it.
Where a 30 mm Bore 22200K Series Tapered Bore Spherical Roller Bearings Is Used
At a 30 mm bore, 22200k series tapered bore spherical roller bearings are typically found in electric motors, pumps, gearbox layshafts, machine tool auxiliaries, agricultural machinery and general industrial drives — the volume range of the whole bearing industry.
Failure Modes and What They Look Like
- Subsurface fatigue (spalling) — a flake of raceway lifts out and the bearing gets noisy and rough. This is the failure the L10 life calculation predicts — if it arrives near the calculated life the bearing did its job, and if it arrives early the load, the fit or the lubrication was not what the calculation assumed.
- Inadequate lubrication — a polished, then discoloured, then torn raceway, running hot with a darkened grease. It is the most common cause of early failure by a wide margin, and the interval, not the grease, is usually what was wrong.
- Contamination — dents in the raceway with raised edges, then premature spalling from those dents. Wear particles, casting sand and washdown water all do it; sealing and filtration are what prevent it.
- False brinelling and fretting — evenly spaced dull marks at ball or roller pitch, produced by vibration while the shaft is stationary — a machine that travels on a truck, or a standby pump beside a running one. It is not caused by overload and cannot be cured by fitting a bigger bearing.
- Loss of internal clearance — the whole raceway path is loaded, the bearing runs hot from installation and it discolours evenly. The fit was too heavy, the shaft ran hotter than the housing, or a CN bearing was fitted where C3 was needed.
- Seal failure — grease escaping, then water and dirt getting in. A contact seal is a wearing part with a temperature limit of its own, and a washdown at 80 °C will get past a standard nitrile lip long before the bearing itself is in trouble.
Where NOT to Use a 22200K Series Tapered Bore Spherical Roller Bearings
- Do not treat the self-alignment as unlimited. A spherical roller bearing accommodates a fraction of a degree to a couple of degrees depending on the series and the seal — beyond that the rollers run off the end of the raceway.
- Do not load one almost purely axially. The two rows share the load through the spherical raceway; a nearly pure thrust load unloads one row completely, and the unloaded row skids.
- Do not drive a tapered-bore bearing up its adapter sleeve by feel. The drive-up is measured — as clearance reduction or as axial travel — because too far removes the internal clearance the bearing needs to survive.
- Do not treat a sealed bearing as sealed for life in a wet or hot environment. A contact seal has a temperature and a pressure limit of its own, and once it is past them the grease leaves and the water arrives.
