Pressed Steel Cage 1300K Series Tapered Bore Self-Aligning Ball Bearings are dimensioned to ISO 15 / GB/T 281 / DIN 630 exactly as the standard version is: the material changes the properties, never the envelope. What it does change — as the rings — it relies on the lubricant and the seals, magnetic and the service range not the limiting element; the lubricant and the ring heat stabilization decide — is set out below with the full size chart.
Why Pressed Steel Cage for 1300K Series Tapered Bore Self-Aligning Ball Bearings
The standard cage of volume bearing production: light, cheap, tolerant of temperature and unaffected by the oils that age a polymer cage. In a 1300k series tapered bore self-aligning ball bearings it is the cage, which spaces the rolling elements and keeps them from touching each other.
Pressed from sheet and guided by the rolling elements, it adds almost no mass and almost no cost, tolerates a wide temperature range, and is unaffected by lubricant chemistry. It is the default cage of the standard bearing ranges for good reasons.
Material Properties
| Grade designation | low-carbon sheet steel, two-piece riveted or ribbon type, rolling-element guided |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | Not the limiting element; the lubricant and the ring heat stabilization decide |
| Corrosion characteristic | As the rings — it relies on the lubricant and the seals |
Service Limits
It is a light-duty cage: it is guided by the rolling elements and it is not intended for heavy vibration, high acceleration or sustained very high speed, which is where the machined brass cage takes over. In a heavily shocked application, cage damage rather than raceway fatigue is what ends the bearing.
Alternatives and When to Switch
Polyamide where quiet running and low friction matter and the temperature is moderate; machined brass where speed, shock or lubricant chemistry rules both of the others out.
Fitting a Steel Bearing in an Aluminum Housing
Aluminum has roughly twice the coefficient of thermal expansion of bearing steel, so a housing bore machined to a normal H7 fit at room temperature grows away from the outer ring as the machine reaches operating temperature. The outer ring then turns in its seat and wears the bore. Where the housing is aluminum and the temperature rise is more than about 30 degrees C, tighten the housing fit by one grade — J7 or K7 in place of H7 — or fit a steel sleeve into the aluminum. Check the resulting internal clearance: a tighter housing fit takes clearance out of the bearing, which is often why C3 is specified alongside it.
Sizes of 1300K Series Tapered Bore Self-Aligning Ball Bearings Available in Pressed Steel Cage
| Designation | Bore d (mm) | Outer diameter D (mm) | Width B (mm) | Chamfer r min (mm) | Bore taper | Adapter sleeve | Permissible misalignment (deg) |
|---|---|---|---|---|---|---|---|
| 1305K | 25 | 62 | 17 | 1.1 | 1:12 | H305 | 2.5 |
| 1306K | 30 | 72 | 19 | 1.1 | 1:12 | H306 | 2.5 |
| 1307K | 35 | 80 | 21 | 1.5 | 1:12 | H307 | 2.5 |
| 1308K | 40 | 90 | 23 | 1.5 | 1:12 | H308 | 2.5 |
| 1309K | 45 | 100 | 25 | 1.5 | 1:12 | H309 | 2.5 |
| 1310K | 50 | 110 | 27 | 2 | 1:12 | H310 | 2.5 |
| 1311K | 55 | 120 | 29 | 2 | 1:12 | H311 | 2.5 |
| 1312K | 60 | 130 | 31 | 2.1 | 1:12 | H312 | 2.5 |
| 1313K | 65 | 140 | 33 | 2.1 | 1:12 | H313 | 2.5 |
| 1314K | 70 | 150 | 35 | 2.1 | 1:12 | H314 | 2.5 |
| 1315K | 75 | 160 | 37 | 2.1 | 1:12 | H315 | 2.5 |
| 1316K | 80 | 170 | 39 | 2.1 | 1:12 | H316 | 2.5 |
| 1317K | 85 | 180 | 41 | 3 | 1:12 | H317 | 2.5 |
| 1318K | 90 | 190 | 43 | 3 | 1:12 | H318 | 2.5 |
| 1319K | 95 | 200 | 45 | 3 | 1:12 | H319 | 2.5 |
| 1320K | 100 | 215 | 47 | 3 | 1:12 | H320 | 2.5 |
