Material specification page for hk-2rs series sealed drawn cup needle roller bearings in GCr15 Bearing Steel. Covers the grade designation (GCr15 (GB/T 18254) = 100Cr6 (1.3505) = SAE 52100, through-hardened to 58–64 HRC), what the material does inside the bearing, its temperature and environmental limits, the alternatives worth considering, and the sizes available to ISO 3245 / DIN 618-1.
Why GCr15 Bearing Steel for HK-2RS Series Sealed Drawn Cup Needle Roller Bearings
The default material for the rings and rolling elements of virtually every standard rolling bearing. In a hk-2rs series sealed drawn cup needle roller bearings it is the steel of the rings and, in most designs, of the rolling elements.
Through-hardened high-carbon chromium steel is what a raceway is: hard enough to resist the rolling contact stress, clean enough after modern vacuum degassing that the inclusions which start fatigue cracks are rare, and dimensionally stable after tempering so the ground bore stays the size it was ground to.
Material Properties
| Grade designation | GCr15 (GB/T 18254) = 100Cr6 (1.3505) = SAE 52100, through-hardened to 58–64 HRC |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | To about +120 °C as normally heat stabilized; stabilized rings (S1, S2 and above) extend the limit in steps to around +250 °C |
| Corrosion characteristic | None of its own — the ground surfaces are bare hardened steel and depend on the lubricant, the seals and the preservative for protection |
Alternatives and When to Switch
Move to case-hardened steel where the ring section is heavy or the load is shocked; to 440C where the environment is wet or the part must not rust; and to a hybrid bearing with ceramic balls where the speed, the electrical environment or the lubrication regime is beyond what a steel ball will tolerate.
What the Material Changes About the Bearing
The material does not change the envelope: the bore, the outside diameter, the width and the corner radius stay exactly as the boundary dimension standard fixes them, so the bearing is interchangeable with any other bearing of the same designation. What it changes is what happens inside the contact — the fatigue behavior, the tolerance of shock, and the temperature at which the ring stops being dimensionally stable.
Sizes of HK-2RS Series Sealed Drawn Cup Needle Roller Bearings Available in GCr15 Bearing Steel
| Designation | Bore Fw (mm) | Outer diameter D (mm) | Width C (mm) |
|---|---|---|---|
| HK0810-2RS | 8 | 12 | 10 |
| HK1010-2RS | 10 | 14 | 10 |
| HK1012-2RS | 10 | 14 | 12 |
| HK1210-2RS | 12 | 16 | 10 |
| HK1212-2RS | 12 | 16 | 12 |
| HK1512-2RS | 15 | 21 | 12 |
| HK1612-2RS | 16 | 22 | 12 |
| HK1616-2RS | 16 | 22 | 16 |
| HK1812-2RS | 18 | 24 | 12 |
| HK2012-2RS | 20 | 26 | 12 |
| HK2016-2RS | 20 | 26 | 16 |
| HK2516-2RS | 25 | 32 | 16 |
| HK2520-2RS | 25 | 32 | 20 |
| HK3016-2RS | 30 | 37 | 16 |
| HK3020-2RS | 30 | 37 | 20 |
| HK3520-2RS | 35 | 42 | 20 |
| HK4020-2RS | 40 | 47 | 20 |
