21 catalogued sizes, dimensioned to ISO 15 / DIN 625-1 / GB/T 276. Pick any row and the technical drawing redraws to it.
6200-2RS Series Sealed Ball Bearings to ISO 15 / DIN 625-1 / GB/T 276 are catalogued in bore 10-100 mm, with od 30-180 mm, wide 9-34 mm, r 0.6-2.1 mm. 21 sizes are held in the table below, and the technical drawing redraws to whichever row you select.
Standard
ISO 15 / DIN 625-1 / GB/T 276
Bore
10-100 mm
OD
30-180 mm
Wide
9-34 mm
Catalogued sizes
21
Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering.
Technical Drawing
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the designation snaps the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quotation for 6200-2RS Series Sealed Ball Bearings
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Dimensions & Specifications (ISO 15 / DIN 625-1 / GB/T 276)
Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row.
Designation
Bore d (mm)
Outer diameter D (mm)
Width B (mm)
Chamfer r min (mm)
Seal type
Operating temperature range (u00b0C)
Basic dynamic load rating Cr (kN)
Basic static load rating C0r (kN)
6200-2RS
10
30
9
0.6
Contact rubber seal, both sides
-30 to +110
5.07
2.36
6201-2RS
12
32
10
0.6
Contact rubber seal, both sides
-30 to +110
6.89
3.10
6202-2RS
15
35
11
0.6
Contact rubber seal, both sides
-30 to +110
7.80
3.75
6203-2RS
17
40
12
0.6
Contact rubber seal, both sides
-30 to +110
9.95
4.75
6204-2RS
20
47
14
1
Contact rubber seal, both sides
-30 to +110
13.5
6.55
6205-2RS
25
52
15
1
Contact rubber seal, both sides
-30 to +110
14.8
7.80
6206-2RS
30
62
16
1
Contact rubber seal, both sides
-30 to +110
20.3
11.2
6207-2RS
35
72
17
1.1
Contact rubber seal, both sides
-30 to +110
25.5
15.3
6208-2RS
40
80
18
1.1
Contact rubber seal, both sides
-30 to +110
30.7
19.0
6209-2RS
45
85
19
1.1
Contact rubber seal, both sides
-30 to +110
33.2
21.6
6210-2RS
50
90
20
1.1
Contact rubber seal, both sides
-30 to +110
35.1
23.2
6211-2RS
55
100
21
1.5
Contact rubber seal, both sides
-30 to +110
43.6
29.0
6212-2RS
60
110
22
1.5
Contact rubber seal, both sides
-30 to +110
47.5
32.5
6213-2RS
65
120
23
1.5
Contact rubber seal, both sides
-30 to +110
55.9
40.5
6214-2RS
70
125
24
1.5
Contact rubber seal, both sides
-30 to +110
61.8
45.0
6215-2RS
75
130
25
1.5
Contact rubber seal, both sides
-30 to +110
66.3
49.0
6216-2RS
80
140
26
2
Contact rubber seal, both sides
-30 to +110
72.8
55.0
6217-2RS
85
150
28
2
Contact rubber seal, both sides
-30 to +110
83.2
64.0
6218-2RS
90
160
30
2
Contact rubber seal, both sides
-30 to +110
95.6
73.5
6219-2RS
95
170
32
2.1
Contact rubber seal, both sides
-30 to +110
108
83.0
6220-2RS
100
180
34
2.1
Contact rubber seal, both sides
-30 to +110
124
93.0
6200-2RS Series Sealed Ball Bearings (ISO 15 / DIN 625-1 / GB/T 276) are ball bearings. The full size table is below, followed by the material and cage options, how the bearing is located on the shaft and in the housing, and where the type is and is not the right choice.
What Are 6200-2RS Series Sealed Ball Bearings?
6200-2RS Series Sealed Ball Bearings are ball bearings defined by ISO 15 / DIN 625-1 / GB/T 276. They are selected by bearing designation and the dimensional characteristics shown below. Material, cage and sealing are specified separately from the designation and are covered further down this page.
Materials & Cage
Rings and balls are through-hardened bearing steel — GCr15 / 100Cr6 / SAE 52100 / SUJ2 — at 58 to 64 HRC. AISI 440C martensitic stainless is available where the bearing is washed down or runs wet, at a lower basic dynamic load rating; silicon nitride balls in steel rings raise the speed limit and break the electrical path through the bearing. The cage is a separate decision from the rings and is usually what sets the speed limit: pressed steel as standard, machined brass for shock and high temperature, polyamide PA66 for quiet running and low mass.
6200-2RS Series Sealed Ball Bearings are supplied to order. Pricing starts from approximately US$1.60 per piece for standard bore sizes in bearing steel, open, shielded or sealed, CN clearance; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above.
Specifying the 6200-2RS Series Sealed Ball Bearings
If the shaft is already fixed, go straight to the size: 65 mm bore, 70 mm bore, 75 mm bore and 80 mm bore. Each of those pages repeats only the row that matters for that bore, with the fit and clearance notes underneath it.
The dimensions above are fixed by GB/T 276 and ISO 281 — that is what makes one maker's bearing interchangeable with another's, and it is worth checking which standard a quotation is written to. For the machines and duties this type is actually specified for, see where 6200-2rs series sealed ball bearings are fitted.
Inside the plant
Manufactured in our own plant
This bearing is forged, hardened, ground, superfinished and clearance-set in-house. The stages below are where its tolerance class, its internal clearance and its noise grade are actually decided.
01
Forging & turning
GCr15 bar and tube is cut, heated and forged into ring blanks, then turned to leave a uniform grinding allowance. Forging rather than machining from solid keeps the grain flow following the raceway, which is the surface that eventually fails.
Blank dimensions and grinding stock checked at set-up and per shift.
02
Heat treatment
Through-hardening brings GCr15 / 100Cr6 to 58–64 HRC; carburizing case-hardens 20CrMnTi where the section is heavy or the load is shock. Rings are then stabilized so they hold size in service rather than growing in the housing.
Core and surface hardness per lot; retained austenite and dimensional stability to the ordered temperature class.
03
Raceway grinding
Faces, bore, outer diameter and raceway are ground in sequence on separate machines. This is where the tolerance class is created: P0, P6, P5 or P4 is a grinding outcome, not a sorting outcome.
Bore and outer diameter deviation, raceway roundness and face runout measured to ISO 492 on every setup.
04
Honing & superfinishing
The ground raceway is honed to remove the grinding lay and bring surface roughness down to a fraction of a micrometre. Raceway finish is what decides whether a lubricant film forms, and therefore what decides bearing life far more than the load rating alone.
Surface roughness Ra and waviness measured per lot.
Third-party video, selected automatically for this topic. It is not produced by Bushing Bearings and is not a specification source — use the tables on this page for dimensional data.
Frequently Asked Questions
Which standard applies to 6200-2RS Series Sealed Ball Bearings, and how are they located on the shaft?
6200-2RS Series Sealed Ball Bearings are manufactured to ISO 15 / DIN 625-1 / GB/T 276, which fixes the boundary dimensions on this page. They are mounted with an interference fit on the shaft and a transition or clearance fit in the housing, chosen from the load case and which ring rotates.
Which sizes of 6200-2RS Series Sealed Ball Bearings does Bushing Bearings supply?
The table on this page lists 21 sizes for 6200-2RS Series Sealed Ball Bearings, ranging from 6200-2RS to 6220-2RS. Sizes outside the table can be quoted on request.
In which materials are 6200-2RS Series Sealed Ball Bearings supplied?
6200-2RS Series Sealed Ball Bearings are supplied in through-hardened bearing steel (GCr15 / 100Cr6 / SAE 52100) at 58-64 HRC, with AISI 440C stainless and hybrid ceramic variants. Material is only part of the specification: state the internal clearance group (or preload class), the seal or shield type and the cage material alongside the designation, because all three change the part you receive.
What shaft and housing tolerances suit 6200-2RS Series Sealed Ball Bearings?
The smallest bore on this page is 10 mm. With a rotating inner ring under normal load the shaft is normally machined to k5 or m6 and the housing to H7 or J7, so the inner ring is an interference fit and the outer ring can move axially to take up thermal growth. Reverse the fits when it is the outer ring that rotates. Check the figure against your own load case before machining.
How do I request a quotation?
Use the parametric drawing on this page to set the exact configuration — designation, internal clearance, seal type and cage — and click "Request this configuration". A specialist from Bushing Bearings will respond within one business day.
Need a bearing quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
